TMAX - Buying Guide
Last Updated: 05/24/2024
Share on
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional. #1
TMAX 100 pc 1/2 Inch Sand Drum Grit 60 Coarse with 2 pc 1/8 Inch Mandrel for Dremel Rotary Tools
Asin: B09SXP6GNB | Model: 73009 | PartNumber: 73009 | Ean: 0767531510339 | UPC: 767531510339
Here Are Our Best Practices For Using Sand Drums. 1. Adjusting The Screw At The Top Of The Mandrel Will Loosen Or Tighten The Sand Drum. Make Sure The Sand Drum Is Held Tight To The Mandrel Before Use. 2. During Use, Periodically Power Down The Rotary Tool To Check The Sand Drum. Ensure That There Is Sufficient Grit Remaining On The Band Before Continuing..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
3. Rotary Tools Can Operate At Very High Rpm. High Rpm With A Small Tool Such As A Sanding Drum Produces A Lot Of Friction And Heat Build Up. Ensure That Your Sand Drum And Mandrel Is Not Getting Too Hot. Consider Using Medium Speed And Alternating Mandrels As You Change Sand Drums Out To Reduce Heat Build Up.
4. Rotary Tools Are Power Tools. Always Consider Appropriate Eyewear And Other Ppe To Suit Your Task..
100 Piece 1/2" (12.7Mm) 60 Grit, 1/2" (12.7Mm) Diameter; 2 Piece 1/2" (12.7Mm) X 1/2" (12.7Mm) Rubber Mandrels; 1/8" (3.175Mm) Shank Size (For Dremel And Other Rotary Tools).
Features
- 100 PC 1/2" (12.7mm) sand drum with 2 Mandrel for dremel grit 60 coarse
- 100 piece 1/2 (12.7mm) 60 Grit, 1/2 (12.7mm) Diameter; 2 piece 1/2 (12.7mm) X 1/2 (12.7mm) Rubber Mandrels; 1/8 (3.175mm) shank size (for Dremel and other Rotary Tools)
- Here are our best practices for using sand drums. 1. Adjusting the screw at the top of the mandrel will loosen or tighten the sand drum. Make sure the sand drum is held tight to the mandrel before use. 2. During use, periodically power down the rotary tool to check the sand drum. Ensure that there is sufficient grit remaining on the band before continuing.
- 3. Rotary tools can operate at very high RPM. High RPM with a small tool such as a sanding drum produces a lot of friction and heat build up. Ensure that your sand drum and mandrel is not getting too hot. Consider using medium speed and alternating mandrels as you change sand drums out to reduce heat build up.
4. Rotary tools are power tools. Always consider appropriate eyewear and other PPE to suit your task. - US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 6.00 x 4.00 inches | Weight: 4.00 ounces
See On Amazon #2
TMAX 42 Inch (1 Meter) Flexible Flex Shaft Polishing Chuck for Dremel Rotary Grinder Tools
Asin: B09SXPZ7BC | Ean: 0767531844106 | UPC: 767531844106
Rotary Tools Are Incredibly Versatile And This Accessory Gives You Even More Functions. Plus, The Flexi Rubber Non-Slip Shaft Lets You Take Really Control Over The Job In Hand. Bit Installation Instruction: 1) Insert The L Bar Included Into The Hole At The Collet Side Of The Shaft. 2) Unscrew The Shaft Collet Nut. 3)Insert Bit, Not Included, Into The Shaft Collet 4)Tighten Shaft Collet Nut. 5) Remove The L Bar.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Shaft Installation As Shown In Attached Picture: 1) Remove Rotary Tool Collet Nut, And Rotary Tool Top Cap. 2) Slide Collet Nut Onto Shaft Core. 3)Insert Shaft Core Into Collet. 4) Tighten Collet Nut. Make Sure The Shaft Core Is Hold Tightly In The Tool. 5) Screw Shaft Connector Onto The Rotary Tool. This Will Ensure The Shaft Core Push Back Into The Shaft..
This Is A 42” Grinder Attachment Which Fits The Majority Of Rotary Tools. Connection Is For Head With 3/4" (19.05Mm) Thread. For Dremel Models 100, 200, 300, 3000, 4000, 7300, 7700; Foredom, Toolshop, Performax, Milwaukee M12, Etc. If You're A Diy-Er, Hobbyist Or Craft Worker Turn Your Rotary Tool Into A Grinder With This Flexible Shaft Attachment..
Features
- 42" Rotary Grinder Tool Flexible Flex Shaft for Dremel and compatible rotary tools
- This is a 42 grinder attachment which fits the majority of rotary tools. connection is for head with 3/4 (19.05mm) thread. for Dremel models 100, 200, 300, 3000, 4000, 7300, 7700; Foredom, ToolShop, Performax, Milwaukee M12, etc. If you're a DIY-er, hobbyist or craft worker turn your rotary tool into a grinder with this flexible shaft attachment.
- Rotary tools are incredibly versatile and this accessory gives you even more functions. Plus, the flexi rubber non-slip shaft lets you take really control over the job in hand. Bit installation instruction: 1) insert the L bar included into the hole at the collet side of the shaft. 2) unscrew the shaft collet nut. 3)insert bit, not included, into the shaft collet 4)tighten shaft collet nut. 5) remove the L bar
- Shaft installation as shown in attached picture: 1) remove rotary tool collet nut, and rotary tool top cap. 2) slide collet nut onto shaft core. 3)insert shaft core into collet. 4) tighten collet nut. Make sure the shaft core is hold tightly in the tool. 5) screw shaft connector onto the rotary tool. This will ensure the shaft core push back into the shaft.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 4.00 x 4.00 inches | Weight: 9.00 ounces
See On Amazon #3
TMAX 4 pc Torx Plus 50IP 2 inch Long Bit Socket 1/2 inch Square Drive Auto Repair Impact Ready Tool
Asin: B09Z34724T | Model: 73375 | PartNumber: 73375 | Ean: 0767531504253 | UPC: 767531504253
Sockets Are Made Of Satin Finished Chrome Vanadium Steel With 1/2" (12.7Mm) Square Drive.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool | Industrial Quality For Auto Repair And Air Tools..
Bits Are Made Of S2 Steel For Maximum Durability..
Features
- 4 pc Torx Plus 50IP 55mm 2" Long Bit socket
- Bits are made of S2 steel for maximum durability.
- Sockets are made of satin finished Chrome Vanadium steel with 1/2 (12.7mm) square drive
- Bits are impact ready. Suitable for both hand tool and electric tool | Industrial quality for auto repair and air tools.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 5.00 x 4.00 Inches | Weight: 10.00 ounces
See On Amazon #4
TMAX 7pc 1" T20 Torx Bit Set - Quick Change Star Driver Bits for T20 (T-20) Screws and Heads
Asin: B0BM6WZR68 | Ean: 0767531838518 | UPC: 767531838518
Compatibility: These Impact Rated Torx Bits Allow You To Quickly Drive Torx/Star Head Screws And Fasteners With A T20 Head. 1/4" Drive Hex Shaft For Standard Drills..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Includes: A 7-Pack Of 1" T20 (T-20) Torx Bits With A Convenient Plastic Holder That Displays The Head Size And Pattern..
Durability: Each T20 Torx/Star Driver Bit Is Made Of High Quality S2 Industrial Steel For Long-Lasting Bit Life..
Features
- TMAX 7 Piece 1" T20 Torx Bit Set - Quick Change Star Driver Bits for T20 (T-20) Screws and Heads
- DURABILITY: Each T20 Torx/Star Driver bit is made of high quality S2 industrial steel for long-lasting bit life.
- COMPATIBILITY: These impact rated Torx bits allow you to quickly drive Torx/Star head screws and fasteners with a T20 head. 1/4 drive hex shaft for standard drills.
- INCLUDES: A 7-pack of 1 T20 (T-20) Torx bits with a convenient plastic holder that displays the head size and pattern.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 2.50 x 0.50 inches | Weight: 1.40 ounces
See On Amazon #5
TMAX 1/4 Inch T-Handle Hex Bit Holder Screwdriver, 5 Inch Long
Asin: B09Z33NZK5 | Model: 73165 | PartNumber: 73165 | Ean: 0767531522516 | UPC: 767531522516
3.5 Long Inch Shaft.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Rubberized Soft Grip Handle | T Shaped Handle For Greater Control And Torque.
Holds Standard 1/4" Bits.
Features
- 1/4 Inch T-Handle Hex Bit Holder, 5-Inch long
- Holds standard 1/4 bits
- 3.5 long inch shaft
- Rubberized soft grip handle | T shaped handle for greater control and torque
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 4.50 x 2.50 inches | Weight: 10.00 ounces
See On Amazon #6
TMAX 50pc PH3 Impact Ready Phillips 1 Inch Screwdriver Insert Bits Hex Shank
Asin: B09Z351KV8 | Ean: 0767531601747 | UPC: 767531601747
Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Bits Come In Heavy Duty Storage Container. | Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool.
Made Of S2 Steel For Maximum Durability..
Features
- 50 pc PH3 Phillips 1 Inch (25mm) Screwdriver Insert Bits
- Made of S2 steel for maximum durability.
- Bits are impact ready. Suitable for both hand tool and electric tool
- Bits come in heavy duty storage container. | Bits are impact ready. Suitable for both hand tool and electric tool
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.55 x 3.66 x 2.64 inches | Weight: 10.00 ounces
See On Amazon #7
TMAX 10 pc 1/4 Inch Rubber Mandrel Sand Drum Holder 1/8 Inch Shank for Dremel Rotary Tools
Asin: B09MBQB486 | Model: 73422 | PartNumber: 73422 | Ean: 0767531917084 | UPC: 767531917084
Here Are Our Best Practices For Using Sand Drums. 1. Adjusting The Screw At The Top Of The Mandrel Will Loosen Or Tighten The Sand Drum. Make Sure The Sand Drum Is Held Tight To The Mandrel Before Use. 2. During Use, Periodically Power Down The Rotary Tool To Check The Sand Drum. Ensure That There Is Sufficient Grit Remaining On The Band Before Continuing..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
3. Rotary Tools Can Operate At Very High Rpm. High Rpm With A Small Tool Such As A Sanding Drum Produces A Lot Of Friction And Heat Build Up. Ensure That Your Sand Drum And Mandrel Is Not Getting Too Hot. Consider Using Medium Speed And Alternating Mandrels As You Change Sand Drums Out To Reduce Heat Build Up.
4. Rotary Tools Are Power Tools. Always Consider Appropriate Eyewear And Other Ppe To Suit Your Task..
10 Piece 1/4" (6.35Mm) X 1/2" (12.7Mm) Rubber Mandrels; Used To Hold 1/4" (6.35Mm) Diameter Sand Drum Or Sand Band; 1/8" (3.175Mm) Shank Size For Dremel And Other Rotary Tools.
Features
- 10 pc 1/4" (6.35mm) Rubber Mandrel 1/8 inch Shank Sand Drum Holder for Dremel Rotary tool
- 10 piece 1/4 (6.35mm) X 1/2 (12.7mm) Rubber Mandrels; used to hold 1/4 (6.35mm) diameter sand drum or sand band; 1/8 (3.175mm) shank size for Dremel and other Rotary Tools
- Here are our best practices for using sand drums. 1. Adjusting the screw at the top of the mandrel will loosen or tighten the sand drum. Make sure the sand drum is held tight to the mandrel before use. 2. During use, periodically power down the rotary tool to check the sand drum. Ensure that there is sufficient grit remaining on the band before continuing.
- 3. Rotary tools can operate at very high RPM. High RPM with a small tool such as a sanding drum produces a lot of friction and heat build up. Ensure that your sand drum and mandrel is not getting too hot. Consider using medium speed and alternating mandrels as you change sand drums out to reduce heat build up.
4. Rotary tools are power tools. Always consider appropriate eyewear and other PPE to suit your task. - US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.30 x 3.00 x 3.00 inches | Weight: 0.06 Pounds
See On Amazon #8
TMAX Quick Change Collet Nut Kit Set #4485 Durable for Dremel Rotary Tools
Asin: B09MBR8X4Q | Model: 73072 | PartNumber: 73072 | Ean: 0767531645147 | UPC: 767531645147
Collets Are 3/4" (19.05Mm) Long And For Dremel 225 And Compatible Flex-Shaft Attachment..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Include A Collet Nut And 4 Piece Durable Shiny 1/32” 1/16” 3/32” 1/8” Inch Collet Bit #483 482 481 480 |.
For Dremel Except Discontinued Models 1, 2, And Series 1 Or Earlier Of Discontinued Models 260, 270 And 280. It Also Fit Many Other Compatible Rotary Tools..
Features
- TMAX Quick Change Collet Nut Kit Set 4485 Durable for Dremel
- for Dremel except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280. It also fit many other compatible rotary tools.
- Collets are 3/4 (19.05mm) long and for Dremel 225 and compatible Flex-Shaft attachment.
- include a collet nut and 4 piece durable shiny 1/32 1/16 3/32 1/8 inch Collet bit #483 482 481 480 |
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 inches | Weight: 2.00 ounces
See On Amazon #9
TMAX Flexible Shaft Extension Cord for Rotary Tool Grinder 3148
Asin: B09FZR92W8 | Model: 73450 | PartNumber: 73450 | Ean: 0767531840306 | UPC: 767531840306
To Remove The Broken Shaft: First Pull Out Existing Handle From The Broken Shaft. The Handle Is Secured With Spring Load Metal Ball. Unscrew The Shaft Connector Clockwise From The Grinder ( Note That It Is Reverse Threaded). Pull Down The Metal Shaft Outer Shield To Expose Steel Inner Core. Unscrew The Inner Core From The Grinder Using Included L Bar..
The Shaft Is 3 Feet (1 Meter) Long With Heavy Duty Metal Outer Shield..
To Install The Replacement Shaft: Pull Out Steel Inner Core. Secure The Inner Core To The Grinder With The Included L Shape Bar Wrench. Screw The Shaft Connector Counter Closewise To The Grinder. Slide The End Of Inner Core Into The Groove Inside The Handle. Push Handle Back To The Shaft..
The Shaft Match Tmax Grinder Sku 3148. Handle Is Listed As A Separate Replacement Items..
Features
- TMAX Flexible Shaft Replacement for Grinder 3148 Drill Bit Extension Drill Drive Shaft Flexible Flex Shaft Extension Cord Rotary Tool for Drilling Grinding Polishing
- The shaft match TMAX grinder SKU 3148. Handle is listed as a separate replacement items.
- To remove the broken shaft: First pull out existing handle from the broken shaft. The handle is secured with spring load metal ball. Unscrew the shaft connector clockwise from the grinder ( Note that it is reverse threaded). Pull down the metal shaft outer shield to expose steel inner core. Unscrew the inner core from the grinder using included L bar.
- To install the replacement shaft: Pull out steel inner core. Secure the inner core to the grinder with the included L shape bar wrench. Screw the shaft connector counter closewise to the grinder. Slide the end of inner core into the groove inside the handle. Push handle back to the shaft.
- The shaft is 3 feet (1 meter) long with heavy duty metal outer shield.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 12.00 x 6.00 inches | Weight: 0.63 Pounds
See On Amazon #10
TMAX 25 pc #2 Square Robertson 2 Inch Screwdriver Insert Bits
Asin: B09Z34JSXY | Model: 73194 | PartNumber: 73194 | Ean: 0767531827024 | UPC: 767531827024
Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Bits Come In Heavy Duty Storage Container. | Bits Are 2 Inches Long..
Made Of S2 Steel For Maximum Durability..
Features
- 25 pc #2 Square Robertson 2 Inch (50mm) Screwdriver Insert Bits
- Made of S2 steel for maximum durability.
- Bits are impact ready. Suitable for both hand tool and electric tool
- Bits come in heavy duty storage container. | Bits are 2 inches long.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 5.00 x 3.00 inches | Weight: 0.69 pounds
See On Amazon #11
TMAX 10 pc 2 mm (5/64 Inch) Cut Off Wheel Screw Mandrel 1/8 Inch Shank Holder for Dremel Rotary Tools
Asin: B09MBQF5QJ | Model: 71264 | PartNumber: 71264 | Ean: 0767531994139 | UPC: 767531994139
Used To Hold Cutoff Wheel.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
1/8" (3.175Mm) Shank Size For Dremel And Other Rotary Tools..
10 Piece 2Mm Screw Mandrel.
Features
- 10pc 2mm Screw Mandrel 1/8 inch Shank Cut-off Wheel Holder
- 10 piece 2mm screw mandrel
- used to hold cutoff wheel
- 1/8 (3.175mm) shank size for Dremel and other Rotary Tools.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.25 x 3.00 x 3.00 inches | Weight: 2.00 ounces
See On Amazon #12
TMAX 10 pc Impact Ready 5/16 Inch Magnetic Nutsetter Set 1/4 Inch Shank
Asin: B09Z333TRB | Model: 73264 | PartNumber: 73264 | Ean: 0767531775882 | UPC: 767531775882
The Bit Has 1/4" (6.35Mm) Hex Shank. Total 1.5" Long..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Industrial Strength Magnet Maximizes Fastener Retention. Come With The Storage Box. | Forged With S2 Steel For Maximum Durability. Product Designed For Use In Impact Drivers And Wrenches.
Recessed Corners = Drives On Flats Which Minimzes Shavings.
Features
- Include 10 pc impact ready 5/16" (7.94mm) nutsetter.
- Recessed Corners = drives on flats which minimzes shavings
- The bit has 1/4 (6.35mm) hex shank. Total 1.5 long.
- Industrial strength magnet maximizes fastener retention. Come with the storage box. | Forged with S2 steel for maximum durability. Product designed for use in Impact Drivers and Wrenches
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 inches | Weight: 8.00 ounces
See On Amazon #13
TMAX 10 pc Nylon Plastic Bristle 3/4 Inch Flat Wire Brush #403 1/8 Inch Shank for Dremel Rotary Tools
Asin: B09Z343HG6 | Model: 73409 | PartNumber: 73409 | Ean: 0767531793367 | UPC: 767531793367
Overall Length Is 43Mm (1 3/4 Inch); Shank Diameter : 3.17Mm (1/8 Inch).
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Wheel Diameter : 19Mm (3/4 Inch); Wheel Thickness : 1Mm To 1.5Mm | Suitable For Removing Rust And Oxidation..
They Will Fit Your Hand Drill, Drill Press & For Dremel And Foredom Tool With A 1/8" (3.175Mm) Collet..
Features
- New 10 pieces Nylon Plastic flat wire BRUSHES
- They will fit your hand drill, drill press & for Dremel and Foredom tool with a 1/8 (3.175mm) collet.
- Overall length is 43mm (1 3/4 inch); Shank diameter : 3.17mm (1/8 inch)
- Wheel diameter : 19mm (3/4 inch); Wheel thickness : 1mm to 1.5mm | Suitable for removing rust and oxidation.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 inches | Weight: 4.10 ounces
See On Amazon #14
TMAX 25 pc 1/4 Inch Flat Impact Ready 2 Inch Length Slotted Screwdriver Insert Bit Hex Shank with Quick Release Slot
Asin: B09Z3583B6 | Model: 71276 | PartNumber: 71276 | Ean: 0767531724767 | UPC: 767531724767
Industrial Quality With Quick Release Slot.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Made Of S2 Steel For Maximum Durability. | Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool.
All Bits Are 2" Long With 1/4" (6.35Mm) Shank.
Features
- 25 pc Flat Slotted 1/4" (6.35mm) Screwdriver Insert Bits in a storage box.
- All bits are 2 Long with 1/4 (6.35mm) Shank
- Industrial quality with quick release slot
- Made of S2 steel for maximum durability. | Bits are impact ready. Suitable for both hand tool and electric tool
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 2.00 inches | Weight: 10.70 ounces
See On Amazon #15
TMAX 2 pc 1/4-20 Combination Drill and Tap Multi Use Deburr Countersink Hex Bit
Asin: B09Z34FVLF | Ean: 0767531949542 | UPC: 767531949542
Drill, Tap And Deburr In One Operation. Tapered Tap Design Prevents Thread Damage From Over-Drilling..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
One Piece Construction Guarantees Proper Drill For Tap Size. | 135 Self-Centering Split Point Tip. 10 Gauge (3.5Mm) Capacity. Usage Suggestions: Use Of Cutting Coil Recommended. Clean Tap Of Metal Chips To Extend Life. Reverse Drill To Back Out After Completing Tap..
Made Of High Speed M2 Steel. For Use With: Steel, Copper, Brass, Aluminum. Drill, Tap And Deburr In One Operation..
Features
- 2 pc 1/4-20 Combination Drill and Tap Multi Use Deburr Countersink Hex Bit
- Made of high speed M2 steel. For use with: steel, copper, brass, aluminum. drill, tap and deburr in one operation.
- Drill, tap and deburr in one operation. Tapered tap design prevents thread damage from over-drilling.
- One piece construction guarantees proper drill for tap size. | 135 self-centering split point tip. 10 gauge (3.5mm) capacity. Usage suggestions: use of cutting coil recommended. clean tap of metal chips to extend life. reverse drill to back out after completing tap.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.25 x 3.50 x 4.00 Inches | Weight: 1.00 ounces
See On Amazon #16
TMAX 100 pc 1/4 Inch Sand Drum Grit 60 Coarse with 2 pc 1/8 Inch Mandrel for Dremel Rotary Tools
Asin: B09Z33CLCB | Model: 73607 | PartNumber: 73607 | Ean: 0767531525807 | UPC: 767531525807
Here Are Our Best Practices For Using Sand Drums. 1. Adjusting The Screw At The Top Of The Mandrel Will Loosen Or Tighten The Sand Drum. Make Sure The Sand Drum Is Held Tight To The Mandrel Before Use. 2. During Use, Periodically Power Down The Rotary Tool To Check The Sand Drum. Ensure That There Is Sufficient Grit Remaining On The Band Before Continuing..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
3. Rotary Tools Can Operate At Very High Rpm. High Rpm With A Small Tool Such As A Sanding Drum Produces A Lot Of Friction And Heat Build Up. Ensure That Your Sand Drum And Mandrel Is Not Getting Too Hot. Consider Using Medium Speed And Alternating Mandrels As You Change Sand Drums Out To Reduce Heat Build Up.
4. Rotary Tools Are Power Tools. Always Consider Appropriate Eyewear And Other Ppe To Suit Your Task..
100 Piece 1/4" (6.35Mm) 60 Grit, 1/4" (6.35Mm) Diameter; 2 Piece 1/4" (6.35Mm) X 1/2" (12.7Mm) Rubber Mandrels; 1/8" (3.175Mm) Shank Size (For Dremel And Other Rotary Tools). The Sand Drum Diameter Is The Inner Diameter Excluding The Sand Paper Thickness..
Features
- 100 PC 1/4" (6.35mm) sand drum with 2 Mandrel for dremel grit 60 coarse
- 100 piece 1/4 (6.35mm) 60 Grit, 1/4 (6.35mm) Diameter; 2 piece 1/4 (6.35mm) X 1/2 (12.7mm) Rubber Mandrels; 1/8 (3.175mm) shank size (for Dremel and other Rotary Tools). The sand drum diameter is the inner diameter excluding the sand paper thickness.
- Here are our best practices for using sand drums. 1. Adjusting the screw at the top of the mandrel will loosen or tighten the sand drum. Make sure the sand drum is held tight to the mandrel before use. 2. During use, periodically power down the rotary tool to check the sand drum. Ensure that there is sufficient grit remaining on the band before continuing.
- 3. Rotary tools can operate at very high RPM. High RPM with a small tool such as a sanding drum produces a lot of friction and heat build up. Ensure that your sand drum and mandrel is not getting too hot. Consider using medium speed and alternating mandrels as you change sand drums out to reduce heat build up.
4. Rotary tools are power tools. Always consider appropriate eyewear and other PPE to suit your task. - US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 6.00 x 4.00 inches | Weight: 0.13 pounds
See On Amazon #17
TMAX 25 pc H-5 Hex 5mm Impact Ready 2 Inch Length Screwdriver Insert Bits Hex Shank with Quick Release Slot
Asin: B09Z34H8BZ | Model: 71549 | PartNumber: 71549 | Ean: 0767531666579 | UPC: 767531666579
Industrial Quality With Quick Release Slot.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Made Of S2 Steel For Maximum Durability. | Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool.
All Bits Are 2" Long With 1/4" (6.35Mm) Shank.
Features
- 25 pc H-5 Hex 5mm Screwdriver Insert Bits in a storage box.
- All bits are 2 Long with 1/4 (6.35mm) Shank
- Industrial quality with quick release slot
- Made of S2 steel for maximum durability. | Bits are impact ready. Suitable for both hand tool and electric tool
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 3.00 x 2.00 inches | Weight: 0.69 Pounds
See On Amazon #18
TMAX 10 pc Durable Shiny 1/8 Inch Rotary Tool Collet Bit #480 for Dremel Rotary Tools
Asin: B09MBS7XZP | Model: 71206 | PartNumber: 71206 | Ean: 0767531901922 | UPC: 767531901922
For Dremel Except Discontinued Models 1, 2, And Series 1 Or Earlier Of Discontinued Models 260, 270 And 280. It Also Fit Many Other Compatible Rotary Tools..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Collets Are For Dremel 225 And Compatible Flex-Shaft Attachment. |.
Collets Are All 3/4" (19.05Mm) Long..
Features
- 10 pieces durable shiny Collet bits # 480 for 1/8 (3.175mm) diameter bits.
- Collets are all 3/4 (19.05mm) long.
- for Dremel except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280. It also fit many other compatible rotary tools.
- Collets are for Dremel 225 and compatible Flex-Shaft attachment. |
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 inches | Weight: 0.06 pounds
See On Amazon #19
TMAX T55 3 Inch Long Torx Star 6 Point Black Impact Bit Socket Auto Repair Tool 1/2 Inch Square Drive
Asin: B09Z336JD2 | Model: 71345 | PartNumber: 71345 | Ean: 0767531586037 | UPC: 767531586037
1/2" (12.7Mm) Sqaure Drive With Drive Release Holes..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Drop Forged Black Chrome Moly Steel (Cr-Mo). | Industrial Grade Quality. Suitable For Air Tools And Electric Tools..
The Socket Bit Is 3-1/8" (80Mm) Long..
Features
- Impact Torx Star 6 point Socket Bit T55
- The socket bit is 3-1/8 (80mm) long.
- 1/2 (12.7mm) Sqaure Drive with drive release holes.
- Drop forged black chrome moly steel (CR-MO). | Industrial grade quality. Suitable for air tools and electric tools.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.00 x 3.00 x 1.00 inches | Weight: 4.00 ounces
See On Amazon #20
TMAX 14 pc T10H-T40H Tamper Proof 6 point Security Torx Impact Ready 1 Inch Long Screwdriver Insert Bit Set
Asin: B09Z34ZRRQ | Ean: 0767531583746 | UPC: 767531583746
Industrial Quality With Quick Release Slot.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Made Of S2 Steel For Maximum Durability. | Sizes Included: T10h (X2), T15h(X2), T20h(X2), T25h(X2), T27h(X2), T30h(X2), T40h(X2).
All Bits Are 1" (25.4Mm) Long With 1/4" (6.35Mm) Shank.
Features
- TMAX 14 pc T10H-T40H Tamper Proof Torx Impact Ready 1" (25mm) Long Screwdriver Insert Bit Set
- All bits are 1 (25.4mm) Long with 1/4 (6.35mm) Shank
- Industrial quality with Quick Release Slot
- Made of S2 steel for maximum durability. | Sizes included: T10H (x2), T15H(x2), T20H(x2), T25H(x2), T27H(x2), T30H(x2), T40H(x2)
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 4.00 x 2.50 inches | Weight: 0.19 Pounds
See On Amazon #21
TMAX 10 pc 1/8 to 1/2 Inch Premium Diamond Coated Drill Hole Saw 1/8 Inch Shank for Dremel Rotary Tools
Asin: B09Z34VWX2 | Model: 71082 | PartNumber: 71082 | Ean: 0767531709405 | UPC: 767531709405
Suitable For Use In Drill Hole On Glass, Marble, Tile Or Granite..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
All In 1/8" (3.175Mm) Shank Fit Your Hand Drill, Drill Press & For Dremel And Foredom Tool With A 1/8" (3.175Mm) Collet | Working Length : 35Mm.
Manufactured By Grit 50 Premium Type Diamond Sands Specail For Cutting..
Features
- New assorted 3-12mm (1/8" to 1/2") PREMIUM diamond coated hole saw (total: 10 pcs, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 mm).
- Manufactured by GRIT 50 premium type diamond sands specail for cutting.
- Suitable for use in drill hole on glass, marble, tile or granite.
- ALL in 1/8 (3.175mm) shank fit your hand drill, drill press & for Dremel and Foredom tool with a 1/8 (3.175mm) collet | Working length : 35mm
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 inches | Weight: 0.19 Pounds
See On Amazon #22
TMAX Non Sparking PH0 Phillips #0 Screwdriver, 2-3/8 Inch Working Length, Beryllium Bronze Copper Non Spark
Asin: B0CVW9PC62 | Ean: 0767531633069 | UPC: 767531633069
Specialized Applications: Hazardous Environments, Aerospace, Musical Instruments, And Precision Measurement Devices..
Easy-To-Read: Size Markings Etched Right On The Tool For Quick And Simple Identification..
Ergonomic: Non-Slip, Soft Handle Allows You To Maintain Effective Use While Providing Good Comfort..
Material: Beryllium Bronze (Aka Beryllium Copper) Is High Strength, Non-Sparking, And Non-Magnetic..
Features
- Non-Sparking PH0 Phillips #0 Screwdriver, 2-3/8" Working Length, Beryllium Bronze Copper
- MATERIAL: Beryllium Bronze (aka Beryllium Copper) is high strength, non-sparking, and non-magnetic.
- SPECIALIZED APPLICATIONS: Hazardous environments, aerospace, musical instruments, and precision measurement devices.
- ERGONOMIC: Non-slip, soft handle allows you to maintain effective use while providing good comfort.
- EASY-TO-READ: Size markings etched right on the tool for quick and simple identification.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 1.38 x 8.27 x 3.94 inches | Weight: 0.09 Pounds
See On Amazon #23
TMAX 10 pc Durable Collet Nut #4485 for Dremel Rotary Tools
Asin: B09Z3424H2 | Model: 71197 | PartNumber: 71197 | Ean: 0767531693537 | UPC: 767531693537
Collets Nuts Are For Dremel 225 And Compatible Flex-Shaft Attachment..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Brand New And Made Of High Quality Material For Reliable Performance. | Durable And Long-Lasting For Extended Use..
Will For Dremel Except Discontinued Models 1, 2, And Series 1 Or Earlier Of Discontinued Models 260, 270 And 280. It Also Fits Many Other Compatible Rotary Tools..
Features
- 10 piece Durable Collet Nut Set #4485 for Dremel and other Rotary tools.
- Will for Dremel except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280. It also fits many other compatible rotary tools.
- Collets nuts are for Dremel 225 and compatible Flex-Shaft attachment.
- BRAND NEW and made of high quality material for reliable performance. | Durable and long-lasting for extended use.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 Inches | Weight: 2.00 ounces
See On Amazon #24
TMAX 10 pc #401 Screw Mandrel for Felt Polishing Wheel Or Cone Tip with 1/8 Inch Shank for Dremel Rotary Tools
Asin: B09MBQV7X1 | Model: 71517 | PartNumber: 71517 | Ean: 0767531869307 | UPC: 767531869307
1/8" (3.175Mm) Shank Size. For Dremel And Other Rotary Tools..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
A Shank With Screw Like Head. | Shiny And Durable..
Capable Of Holding Various Polishing Tips Including Wheel And Cone Shapes..
Features
- 10pc Screw Bit Mandrel 1/8 inch Shank Felt Polishing Tip Holder.
- Capable of holding various polishing tips including wheel and cone shapes.
- 1/8 (3.175mm) shank size. for Dremel and other Rotary Tools.
- A shank with screw like head. | Shiny and durable.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 3.00 inches | Weight: 2.00 ounces
See On Amazon #25
TMAX 14 pc T10-T40 Torx 6 point Impact Ready 1 Inch Long Screwdriver Insert Bit Set
Asin: B09Z35JPVX | Model: 73297 | PartNumber: 73297 | Ean: 0767531956816 | UPC: 767531956816
Industrial Quality With Quick Release Slot.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Made Of S2 Steel For Maximum Durability. | Sizes Included: T10 (X2), T15 (X2), T20 (X2), T25 (X2), T27 (X2), T30 (X2), T40 (X2).
All Bits Are 1" Long With 1/4" Shank.
Features
- 14 pc T10-T40 Torx Impact Ready 1" (25mm) Long Screwdriver Insert Bit Set
- All bits are 1 long with 1/4 Shank
- Industrial quality with Quick Release Slot
- Made of S2 steel for maximum durability. | Sizes included: T10 (x2), T15 (x2), T20 (x2), T25 (x2), T27 (x2), T30 (x2), T40 (x2)
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 2.75 x 2.25 inches | Weight: 0.19 Pounds
See On Amazon #26
TMAX Carbide Downcut Inlay Router Bit 1/32 Inch Diameter
Asin: B09Z355LKQ | Model: 73145 | PartNumber: 73145 | Ean: 0767531626665 | UPC: 767531626665
Comes In Convenient Case With Compartment For Each Bit..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Carbide Router Bit Remain Sharp And Give A Superior Cut On Wood. | Spiral Bits Give Very Clean Cuts..
1.5" Length. 1/8" Shank Diameter..
Features
- Carbide Downcut Inlay Router Bit 1/32" dia.
- 1.5 length. 1/8 shank diameter.
- Comes in convenient case with compartment for each bit.
- Carbide router bit remain sharp and give a superior cut on wood. | Spiral bits give very clean cuts.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.25 x 3.50 x 3.00 inches | Weight: 2.00 ounces
See On Amazon #27
TMAX 50 pc Pozi PZ2 Impact Ready 1 Inch Length Screwdriver Insert Bit Hex Shank with Quick Release Slot
Asin: B09Z32ZBH8 | Model: 71273 | PartNumber: 71273 | Ean: 0767531742495 | UPC: 767531742495
Industrial Quality With Quick Release Slot.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Made Of S2 Steel For Maximum Durability. | Bits Are Impact Ready. Suitable For Both Hand Tool And Electric Tool.
All Bits Are 1" (25.4Mm) Long With 1/4" (6.35Mm) Shank.
Features
- 50 pc Pozi #2 (PZ 2) Screwdriver Insert Bits in a storage box.
- All bits are 1 (25.4mm) Long with 1/4 (6.35mm) Shank
- Industrial quality with quick release slot
- Made of S2 steel for maximum durability. | Bits are impact ready. Suitable for both hand tool and electric tool
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 3.00 x 2.00 Inches | Weight: 10.00 ounces
See On Amazon #28
TMAX Abc6/17Pt Wheel Lock Lugnut Anti-Theft Lug Nut Screw Removal Key Socket S3057 for Vw Audi
Asin: B09Z35VXKG | Model: 73344 | PartNumber: 73344 | Ean: 0767531727805 | UPC: 767531727805
To Determine Which Key You Need, Visually Match The Key Pattern To The Locking Lug Nuts On Your Vehicle. Key Compatibility Is Not Based On The Make, Model Or Year Of The Vehicle. When Removing Your Lug Nuts, It Is Best To Evenly Loosen Each Nut On The Wheel As Opposed To Completely Removing One At A Time, This Helps Reduce Pressure On The Remaining Nuts..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Individual Pieces Now Available From Our 23Pc Set! | Not Intended For Use With Impact Wrench.
They Are Used To Remove Wheel Nuts Screw On Car/Truck/Suv.
Features
- TMAX Abc6/17Pt Wheel Lock Lugnut Anti-Theft Lug Nut Screw Removal Key Socket S3057 for Vw Audi
- They are used to remove wheel nuts screw on car/truck/SUV
- To determine which key you need, visually match the key pattern to the locking lug nuts on your vehicle. Key compatibility is not based on the make, model or year of the vehicle. When removing your lug nuts, it is best to evenly loosen each nut on the wheel as opposed to completely removing one at a time, this helps reduce pressure on the remaining nuts.
- Individual pieces now available from our 23pc set! | Not intended for use with impact wrench
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.75 x 1.25 x 0.75 inches | Weight: 0.13 Pounds
See On Amazon #29
TMAX 2 pc 4486 Multipro Keyless Chuck for Dremel Rotary Tools
Asin: B09G1LWY52 | Model: 73146 | PartNumber: 73146 | Ean: 0767531531709 | UPC: 767531531709
Now Have Tool-Free Accessory Changes; Eliminate The Need For Collet And Wrench When Changing Accessories.
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
Accepts All Accessory Rotary Bits With 1/32" To 1/8" Shanks; Use With Rotary Tool Models 4000, 400, 3000, 398, 395, 300, 285, 275, 200, 100, 8220, 8200, 8050, 800, 780, 770, 7700, 750 | Also For Dremel Attachments 212, 225, And 575.
Keyless Chuck For All Standard Size Rotary Tools And Flexible Hose Shafts. Simplify And Speed Up Your Project..
Features
- TMAX 2pc 4486 MultiPro Keyless Chuck for Dremel and Compatible Rotary Tools
- Keyless chuck for all standard size rotary tools and flexible hose shafts. Simplify and speed up your project.
- Now have tool-free accessory changes; Eliminate the need for collet and wrench when changing accessories
- Accepts all accessory rotary bits with 1/32 to 1/8 shanks; use with rotary tool models 4000, 400, 3000, 398, 395, 300, 285, 275, 200, 100, 8220, 8200, 8050, 800, 780, 770, 7700, 750 | Also for Dremel attachments 212, 225, and 575
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 0.50 x 4.00 x 3.50 inches | Weight: 1.00 ounces
See On Amazon #30
TMAX Rotary Tool Hold Hanger Stand Clamp for Dremel Foredom and Other Rotary Tools
Asin: B09SXP31R6 | Model: 73005 | PartNumber: 73005 | Ean: 0767531537374 | UPC: 767531537374
Hanger Swivels 360-Degrees For Superior Versatility And Easy Access. Steel Rod And Hanger With Mirror Chrome Finish; Rugged Non-Conductive, Non-Scratch Abs Base..
Us-Based Customer Service: Available By Chat, Email, Phone, Or Visit Us At Our Customer Service Center In La Crosse, Wi..
The Item On Sale Is The Rotary Tool Holder Only. Please See Other Listings For Rotary Tool, Accessories And Flexible Shaft..
3-Section Steel Rod Allows Customized Tool Height, Adjusts Easily From 10 - 22 Inches. Heavy-Duty Table-Bench Clamp Can Be Used Horizontal Or Vertical; 2-1/2 Inch Clamping Capacity.
Features
- Super-handy rotary tool accessory - keeps tool handy, out of the way; essential for flex shaft use
- 3-section steel rod allows customized tool height, adjusts easily from 10 - 22 inches. Heavy-duty table-bench clamp can be used horizontal or vertical; 2-1/2 inch clamping capacity
- Hanger swivels 360-degrees for superior versatility and easy access. Steel rod and hanger with mirror Chrome finish; rugged non-conductive, non-scratch ABS base.
- The item on sale is the Rotary Tool Holder only. Please see other listings for rotary tool, accessories and Flexible Shaft.
- US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI.
- See more on Amazon...
Brand: TMAX | Manufacturer: Golden Coulee
Dimensions: 3.00 x 10.00 x 3.00 inches | Weight: 13.00 ounces
See On Amazon