Best Optical Sensors - Buying Guide
Last Updated: 05/26/2024
Share on
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional. #1
Taiss/1 Pair photoelectric Switch 0-20M Through-Beam Reflection Optical Photoelectric Beam Sensor NPN NO photoelectric Sensor Switch 6-36V Proximity Switch with Infrared Ray Beam E3F-20DNL-Z-12MM
Asin: B07VPSSLBR | Model: E3F-20DNL | PartNumber: E3F-20DNL | Ean: 0740306846369 | UPC: 740306846369
Features
- This product is widely used in outdoors gates, garage doors, Weatherproof (IP66) construction for indoor/outdoor usage etc.
- Supply Voltage:6-36V DC;Type : NPN normally open ;Wire Type : DC 3 Wire,Proximity-sensing / Opposite Type
- Sensory Distance : 0-20m Sending Light : Infrared Rays;Current : 300mA;Thread diameter: 12mm/0.47
- Body Size 66mm x12mm/2.6 x0.47(Max.D*L);Cable Length : 120cm/47;Weight : 70g
- Package Content: 1 Pair x Photoelectric Switch+2 x Mounting Bracket
- See more on Amazon...
Sensory Distance : 0-20M;Sending Light : Infrared Rays;Current : 300Ma;Thread Diameter: 12Mm/0.47".
Package Content: 1 Pair X Photoelectric Switch+2 X Mounting Bracket.
Body Size:66Mm X12mm/2.6" X0.47"(Max.D*L);Cable Length : 120Cm/47";Weight : 70G.
Supply Voltage:6-36V Dc;Type : Npn(Normally Open );Wire Type : Dc 3 Wire,Proximity-Sensing / Opposite Type.
Brand: Taiss | Manufacturer: Taiss
See On Amazon #2
MakerHawk 6pcs Optical Endstop with 1M Cable Optical Switch Sensor Photoelectric Light Control Optical Limit Switch Module for 3D Printer
Asin: B07PMW2QMT | Model: 2HW144083OG5A | PartNumber: 2HW144083OG5A | Ean: 0673400167101 | UPC: 673400167101
Features
- VCC: 2.7V to 5V.
- The trigger is sensitive and quiet.
- With high repeatability and no mechanical collision.
- Using optically transmissive principles of design, no loss, no noise with a longer life.
- SIG logic: output low level when there is no trigger and high level when there is trigger.How to trigger the photoelectric: Use the stopper to trigger the limit when it moves to the middle of the red contact groove (it is recommended not to use a transparent material stopper)
- See more on Amazon...
With High Repeatability And No Mechanical Collision..
Sig Logic: Output Low Level When There Is No Trigger And High Level When There Is Trigger.How To Trigger The Photoelectric: Use The Stopper To Trigger The Limit When It Moves To The Middle Of The Red Contact Groove (It Is Recommended Not To Use A Transparent Material Stopper).
Using Optically Transmissive Principles Of Design, No Loss, No Noise With A Longer Life..
The Trigger Is Sensitive And Quiet..
Brand: MakerHawk | Manufacturer: MakerHawk
Dimensions: 0.39 x 1.38 x 0.43 Inches
See On Amazon #3
XINGYHENG 50Pcs TCRT5000L TCRT5000 Photoelectric Sensors Reflective Optical Sensor with Transistor Output Infrared 950mm 5V 3A for Tracking and Obstacle Avoidance Car
Asin: B01N2HVRQP | Model: jpsj-0313-1097 | PartNumber: jpsj-0313-1097 | Ean: 0714973094712 | UPC: 714973094712
Features
- High quality, 100% Brand New.
- Package: 50 PCS TCRT5000 Photoelectric Sensors
- Model No. : TCRT5000L TCRT5000
- Compact construction, sense the presence of an object by using the reflective IR beam from the object.
- Used for some toy car or any other test.
- See more on Amazon...
Model No. : Tcrt5000l Tcrt5000.
Used For Some Toy Car Or Any Other Test..
Compact Construction, Sense The Presence Of An Object By Using The Reflective Ir Beam From The Object..
Package: 50 Pcs Tcrt5000 Photoelectric Sensors.
Brand: XINGYHENG | Manufacturer: XLX
See On Amazon #4
JESSINIE ADNS-3080 Optical Flow Sensor Module Horizontal Movement Detector APM2.52 APM2.6 Light Flow Detector Module Board DIY Kit Electronic PCB
Asin: B0BBLV832W | Model: ADNS-38 | PartNumber: ADNS-38
Features
- High speed motion detection up to 40 ips and 15g, New architecture for greatly improved optical navigation technology
- Programmable frame rate over 6400 frames per second, SmartSpeed self-adjusting frame rate for optimum performance
- Serial port burst mode for fast data transfer, 400 or 1600 cpi selectable resolution, Single 3.3 volt power supply
- Four-wire serial port along with Chip Select, Power Down, and Reset pins
- Suitable for game consoles and computer games, Mice for desktop PC s, Workstations, and portable PC s, Trackballs, Integrated input devices
- See more on Amazon...
Serial Port Burst Mode For Fast Data Transfer, 400 Or 1600 Cpi Selectable Resolution, Single 3.3 Volt Power Supply.
Suitable For Game Consoles And Computer Games, Mice For Desktop Pc’S, Workstations, And Portable Pc’S, Trackballs, Integrated Input Devices.
Four-Wire Serial Port Along With Chip Select, Power Down, And Reset Pins.
Programmable Frame Rate Over 6400 Frames Per Second, Smartspeed Self-Adjusting Frame Rate For Optimum Performance.
Brand: JESSINIE | Manufacturer: JESSINIE
Dimensions: 1.06 x 1.22 x 1.02 inches
See On Amazon #5
2Pcs Optical Sensor TRANSMISSIVE/Slotted Interrupter Limit Switch EE-SX674 for Linear Rail Guide Actuator
Asin: B082FFNH5P | Model: EE-SX674 | PartNumber: EE-SX674 | Ean: 8414796183083
Features
- Working voltage 5-24v wide voltage start
- 1KHz High response frequency
- With 1m flexible link cable
- Small size and easy installation
- 100% Matches Heechoo Linear Guide Rails
- See more on Amazon...
With 1M Flexible Link Cable.
100% Matches Heechoo Linear Guide Rails.
Small Size And Easy Installation.
1Khz High Response Frequency.
Brand: Heechoo | Manufacturer: Heechoo
Dimensions: 0.00 x 1.02 x 0.00 inches
See On Amazon #6
Teyleten Robot IR Infrared Slotted Optical Optocoupler Module Speed Measuring Sensor 3.3V to 5V Photo Interrupter Sensor for Arduino 10pcs
Asin: B08977QFK5 | Ean: 8424515612220
Features
- use: 1. +5 +5 is the positive input port of the power supply, which can be connected to a voltage of 3.3V~5V
- 2. GND GND is the negative input port of the power supply. OUT OUT is the signal output port, which is connected to the I/O port of the single-chip microcomputer. Generally, it is connected to an external interrupt.
- For other main control boards or higher-level main control boards (such as Arm), if you need to set the I/O port to input/output mode, you must set it to input mode/receive mode, otherwise it cannot be used. 51 series MCU can be used directly, no need to set input and output mode
- Note: For Arduino players should set the MCU's I/O port to input mode/receive mode, otherwise it cannot be used.
- See more on Amazon...
For Other Main Control Boards Or Higher-Level Main Control Boards (Such As Arm), If You Need To Set The I/O Port To Input/Output Mode, You Must Set It To Input Mode/Receive Mode, Otherwise It Cannot Be Used. 51 Series Mcu Can Be Used Directly, No Need To Set Input And Output Mode.
Note: For Arduino Players Should Set The Mcu's I/O Port To Input Mode/Receive Mode, Otherwise It Cannot Be Used..
2. Gnd Gnd Is The Negative Input Port Of The Power Supply. Out Out Is The Signal Output Port, Which Is Connected To The I/O Port Of The Single-Chip Microcomputer. Generally, It Is Connected To An External Interrupt..
Brand: Teyleten Robot | Manufacturer: Teyleten Robot
See On Amazon #7
HiLetgo 5pcs LM393 Correlation Photoelectric Sensor Opposite-type Infrared Count Sensor
Asin: B01HXU1WME | Model: 3-01-1140-B | PartNumber: 3-01-1140-B
Infrared Count Sensor.
Photoelectric Sensor.
Brand: HiLetgo | Manufacturer: HiLetgo
See On Amazon #8
DAOKI 5Pcs Speed Measuring Sensor IR Infrared Slotted Optical Optocoupler Module Photo Interrupter Sensor for Motor Speed Detection or Arduino with Encoders
Asin: B081W4KMHC | Model: GR-US-227 | PartNumber: GR-US-227
Features
- Infrared detection, eliminating the interferences of external stray light
- Schmitt trigger, stable wave form and signals
- Signal output indicator (while breaking the beam, outputs low level, the indicator lights up)
- Power: 3.3V to 5V
- Dimension: 26.8mm x 15mm x 18.7mm
- See more on Amazon...
Signal Output Indicator (While Breaking The Beam, Outputs Low Level, The Indicator Lights Up).
Dimension: 26.8Mm X 15Mm X 18.7Mm.
Power: 3.3V To 5V.
Schmitt Trigger, Stable Wave Form And Signals.
Brand: DAOKI | Manufacturer: DAOKI
See On Amazon #9
Taiss/ 1 Pair Photoelectric Sensor M18 Infrared Ray Through-Beam Reflection Optical Photoelectric Switch Sensor NPN NO 6-36VDC Proximity Switch Inductive Distance 5M with mounting Bracket E3F-5DN1
Asin: B07PD9LCK1 | Model: E3F-5DN1 | PartNumber: E3F-5DN1 | Ean: 0741663836765 | UPC: 741663836765
Features
- Product Name : Photoelectric Switch;Sending Light : Infrared Rays;Model :E3F-5DN1
- Wire Type : DC 3 Wire, Proximity-sensing / Opposite Type;Type : NPN NO ;Voltage : DC 6-36V
- Current : 300mA;Sensory Distance : 5m;Head Diameter : 1.6cm/0.6'' ; Thread diameter: 18mm
- Body Size : 2.3 x 7cm/0.9 x 2.7'' (Max.D*L);Material : Plastic, Alloy;Color : Black, Orange
- Cable Length : 120cm/47'';Weight : 110g;Package Content : 1 Pair x Photoelectric Switch + 2 x mounting bracket
- See more on Amazon...
Current : 300Ma;Sensory Distance : 5M;Head Diameter : 1.6Cm/0.6'' ; Thread Diameter: 18Mm.
Cable Length : 120Cm/47'';Weight : 110G;Package Content : 1 Pair X Photoelectric Switch + 2 X Mounting Bracket.
Body Size : 2.3 X 7Cm/0.9" X 2.7'' (Max.D*L);Material : Plastic, Alloy;Color : Black, Orange.
Wire Type : Dc 3 Wire, Proximity-Sensing / Opposite Type;Type : Npn No ;Voltage : Dc 6-36V.
Brand: Taiss | Manufacturer: Taiss
See On Amazon #10
EC Buying 10PCS IR Infrared Sensor Module Slotted Optical Optocoupler Speed Measuring Sensor Module Photo Interrupter Sensor Motor Speed Detection Robot for Arduino
Asin: B0CHDRF497
Features
- Adopting a slot type photoelectric sensor, it consists of an infrared light-emitting diode and an NPN photoelectric transistor, with a slot width of 5.9mm.
- As long as a non-transparent object passes through the slot, it can trigger to output a low TTL level.
- Using Schmidt trigger to jitter pulses is very stable and can be used for small car speed measurement, distance measurement, and other applications!
- Install holes with M3 screws at both ends.
- Working voltage: 3.3V-5V, output form: digital switch output (0 and 1)
- See more on Amazon...
Using Schmidt Trigger To Jitter Pulses Is Very Stable And Can Be Used For Small Car Speed Measurement, Distance Measurement, And Other Applications!.
Working Voltage: 3.3V-5V, Output Form: Digital Switch Output (0 And 1).
Install Holes With M3 Screws At Both Ends..
As Long As A Non-Transparent Object Passes Through The Slot, It Can Trigger To Output A Low Ttl Level..
Brand: EC Buying | Manufacturer: EC Buying
See On Amazon
Looking For Something Else?
Search